Training Fabrics

Design, photo walls fabric wall as a decorative element is returned and becomes fashionable again. Beautiful fabric on the walls recall the historic interiors, when the walls trimmed with various jacquard fabrics or tapestries. Decorative fabrics are an important component of the composition of furniture apartment, they may depend on the emotional coloring of a general nature and your own unique interior. Selection of fabric for the walls The most important condition for the selection of wall tissue is that tissue should be relatively resilient and resistant to contamination. For the walls are perfect cotton, linen and cotton blend with linen, viscose or wool.

May be used for walls furniture fabric, as it is a result of special processing moves moisture well. Do not use fiberglass cloth, as they may cause some difficulties in further operation. Especially for producing fabric wall hangings width of 3 m. It should be borne in mind that the length of the blade must fit the width of the wall with a reserve for securing fabric in the corners. When choosing decorative fabrics for the walls is important to consider not only their utilitarian purpose, but also to seek harmony among all available in the flat elements.

For example, one-color fabrics combine well with almost any environment, and in small apartments, where the rooms directly communicate with each other, can be used tissues of the same figure, but with different shades of colors. This technique facilitates the visual association premises, as it were, at the same time expanding the space of the apartment and creating a harmonious interior. Technology Training fabric walls fabric Due to the fact that the fabric when wet and drying can provide a strong contraction, it must first check on a separate piece (it wet and dry). If you find that much fabric goes down, soak it all and dry. With a little shrinkage of fabric can be used: it is only contribute better stretching it to the surface. Preparation of Pre-wall surface of the walls is necessary to prepare the way for pasting self-adhesive film: it must be absolutely smooth and proshpaklevannoy. Best use glue based on CMC, mastics, casein glue and flour paste. Securing the fabric on the wall before fastening the fabric wall covered with a thin layer of glue and then placing the fabric and smooth it brush from the middle of the canvas to the edges of the "Christmas tree", all the while controlling the junction with adjacent linen. Attach fabric to the wall can also use the strips or frames. With this method of finishing first on the wall of wooden planks are fixed thickness of 10 mm from the ceiling, the floor at the left edge of the wall, around doors and windows. Small pieces of planks also have around switches and outlets. At the right edge of the wall plates are fixed, along with a cloth. After fixing brackets wall between them is covered with foam plates 16 mm thick, thereby improving sound insulation. Then the fabric straps nailed to the edges of the wall and only then cut out the contours of the doors and windows and lined the edge of the corner. Once the fabric is stretched, cut out holes for outlets and switches. At the end of finishing the top and bottom edges of the trim frame rail or rim of tissue.

Venetian

When deciding what to build, pergola or arbor, we must first consider how hard it will be used and in what capacity. Fun Stuff – this is usually a place for solitude, more intimate, I suppose … Arbor in the garden of good, in a secluded corner of suburban area. If we are talking about 'Gulbara', which will gather a small company, or even less, located fireplace – fireplace (as in this case), the choice should be clear made in favor of pergolas. Since most of its mission – the creation of semi-shade for the comfort of a sunny day and the allocation of visual recreation she performs at 100%.

At the same time – the sky above your head, not the roof gazebo, it is enough a large area that would not feel 'in the room' under our feet – the grass or stone, but not half the arbor. The design is light, delicate and not 'pushing'. Pergolas designs – great many of the canons, and then some. (Similarly see: Adroll Marketing Platform). Chief among them – the roof pergolas should be capable of sunlight in the morning and evening, when they are hot. And to escape their day in the sun. A sort of kind of roof – Venetian blinds. Typically, this role is played wide boards set on edge vertically or at an angle, and oriented along an east-west.

Then morning and evening sun shines along the boards and beams easily penetrate between the boards. Day of the same rays of light across the board, and significant part of their boards of late. Inside the pergola is formed in partial shade. Having defined the configuration of the pergola and it is designed, you can proceed to its construction. In most cases, pergolas constructed entirely of tree. And in rare cases – do support the stone. The stone building on the procedure more cumbersome and expensive.

The Thermostat

To work Teplolux MINI-ready after just three days after the installation – a twisted pair cable is only valid for 28 days (the time of complete solidification of the solution to SNP). As a self-regulating heating cable Teplolux-MINI can be decomposed into a heated area of any shape. Is it necessary insulation? Yes, it is necessary. The fact is that due to the thermal conductivity of approximately 50% of heat from the heating cable goes down, overlap, and if you do not want to heat the ceiling and the neighbor to pay extra for electricity, it is best not to neglect the thermal insulation. Good and reliable insulation is cork topped with a layer of foil-plug is not transmits the heat down, and additional foil reflects heat back into the concrete screed.

All mounting underfloor heating – in one box! The price package includes everything you need: self heating cable, mounting tape (Galvanized metal rails for ease of installation and maintenance of a constant step stacking cable – not included in Teplolux-MINI), corrugated tube for floor sensor and a detailed instruction Installation of the system. You only have to choose your thermostat, complete with that is the floor sensor. How much power does a warm floor? Underfloor heating works fully automatically – you just expose the thermostat to the desired temperature the floor, and then the thermostat turns the very floor where you given temperature is established, and include it when the temperature drops below the set. Hours of floor heating – 6 to 12 hours a day, depending on the season, insulation, etc. Accordingly, multiplying the capacity of the chosen cable for 6 and 12, you get the minimum and maximum power consumption of a warm floor in kW / hours. Now the cost of kW / h – 88 kopecks. Is it safe to the floor heating system TEPLOLUX? Yes, of course. In floor heating ‘Teplolux’ has all the certificates to prove it.

Mineral Wool

Transportation and storage of mineral wool plate is carried out according to GOST 25880-83 and in accordance with the requirements of this specification. For transportation to maximize capacity or carrying capacity of wagons, containers, or universal motor. Mineral wool board is transported by all modes of transport in closed vehicles in accordance with the rules of carriage of goods effective for this type of transport. Allowed transportation boards in open vehicles to a distance of 500 km with optional coating them with a tarpaulin or other waterproof material. During transportation, storage overload or consumer panels, unprotected from moisture, responsible for the quality of plates is the consumer. When loading, unloading, transportation and storage of plates should be made to ensure that protection from mechanical damage Shipment consumer panels produce no earlier two-day exposure to the stock. When manually loading or unloading of plates packed weight room should not exceed 50 kg. Plates should stored separately packaged by brand and size in closed warehouses or under a canopy. Plates can be stored without packaging CONDITIONS, preventing them from moisture and mechanical damage. Mineral wool board

Donetsk People

Practice has shown that it was the right decision. On the one hand, some of it is simply impossible to entrust it to someone else. On the other, despite the fact that we are all over the winter very well thought out, in the process Work is still minor problems arose, it was necessary to make decisions quickly, adjust plans, there were unforeseen difficulties that could solve only by us. Spring was another unsuccessful attempt to resolve the issue water. Realizing that there is no water again, we left this venture and focus on the actual construction. In terms of rainfall this year for us turned out to be successful.

Last year we suffered from the drought, it was a lot of downtime. The same summer rains interspersed with clear weather and lack of water almost all the time. Plus, this year reached an agreement with a local farmer, and at critical moments, and there were only two of the season, he brought us water in the barrel of the village. For help us in making bricks, we invited people for a few days to those who wished could come and learn to make adobe on our site. Thus, we have visited a lot of people which on one hand helped us, on the other have their own cob experience. Assistance was essential to all who have visited, we express our sincere thanks.

But a large construction site in earnest to expect such assistance not worth it. Most of the bricks made ourselves and young people, our supporters who came for a few weeks or months to get experience in construction and odd jobs in the settlement. We have been working guys Odessa, Zhytomyr, Donetsk region, helped also by one of our neighbors. With all the while working to establish the most cordial relations. We paid for the work based on the number of bricks made.

Repair Roofs

The service life of roll coatings depends on the quality of base materials, the right technology and type of mastic, and the quality of care for the roof. Roofing materials rolled in the summer under intense heating, which leads to the formation of blisters in the roof membrane, as in the pores of wet basement increases the water vapor pressure (heating mat to 60 C, the vapor pressure dostigaet2 t/m2). With high humidity coating occurs delamination of the carpet, followed by the formation of air and water bags, streaming bitumen mastic carpet heating by solar radiation or mechanical damage to the carpet. The size of air bubbles can reach height of 25-30 sm.V indoor toilets in the upper floors of combined roof can be seen on the ceilings Condensation moisture. The reason for this is the wrong device sewer riser joints with exhaust pipes, sockets set down, resulting in wetting of insulation and thermal insulation qualities of the combined drop in the roof. Current repair of the roof of roll material basically comes down to replacing of defects and clamped all kinds of holes and cracks of the coating.

Places where the roof covering clearing violated, then coated with cement and stick with a roofing material. Places where the roll material to be cut is rotten. Cut the material around the damaged area with a minimum width of 10 cm The resulting groove is carefully cleaned, smeared with putty and stick with a piece of rolled material, so that the edges do not fall for the old roof, ie, butt. Then again OST seat cover with putty and stick with a second layer of roll material, but in this layer should overlap the edges of the damaged area by 15 sm.V when painting the carpet has lagged behind the base, promazyvayut base paste, pressed him canvas mat, and stick the patch on top, overlapping in places cut the carpet at 10 locations sm.V roof membrane blistering cross incision made, turn down the cloth on the carpet four sides, carefully clearing the ground, dried and lubricated it with mastic bent piece of cloth is pressed against the base of the carpet and stick again, and on top of that place and stick the patch to restore the protective krovli.Pri coating repair work, as in roofing, roofing material must be cleared from spreading.

Flat Floor Gives Beauty

Flat floor adds beauty to any room – this is the strength and you. To align the need to: 1. Leveling compound. 2. Ground. 3. Trowel.

Roller with a bucket and mixer (elektromeshalka). Technology of the work: be careful with the carrier surface to a patch filled with equalizer, not cracked. Next, begin to scrape away the plaster, and floors clean of excess cement. Dents in the floor more than 1 cm should be repaired and cleaned what floor (vacuum). For check the bearing surface on the porosity, it is necessary to pour water on the cleaned floor (third-quarter cup). If the water is completely absorbed in one minute, then it means you have to wake your coat about sex.

Apply primer recommend a paint roller (like paint), and then dry it. To prepare the mortar take a bucket of water (dilute solution in a bucket full of water). To obtain a homogeneous mass to the final Stir it with a stirrer (electromechanical). After the solution takes the form of a liquid and a homogeneous (without clots), it should be left in the bucket for a few minutes. After that, take a bucket and pour the solution on the far wall in room. The solution was diluted with a trowel. During the leveling trowel be careful on the surface there was no foreign particles, lumps, clots. The thickness of the first layer should be no more than 1cm. Then, in the same way impose a second layer, but only after the first was almost cured, but not quite dry. Again, start priming. Thick layer of leveling composition of the solution is not used often and is really only for very uneven floors. Plank floor leveling order to properly lay linoleum, you should remove all the irregularities inherent in the wooden floor. In this paper, we describe all the stages of this work. Tools and materials needed for of work. 1. Sheets of plywood (size and thickness of discretion). 2. Rolled insulation (mineral material). 3. Electric drill, screwdriver. 4. Fiberboard. Technology alignment plank floor: 1) When selecting plywood Refer the following rule: the bigger bumps on your floor, the thicker the material to be applied. 2) It is also recommended for additional insulation to lay roll insulation of mineral materials. 3) Adjust the plywood sheeting under the entire floor surface, and cut off the excess. 4) Assess the stability of plywood (walk through it), and if there are places where the plywood sags, then place them under pieces of fiberboard. It is recommended to mark problem areas in the event of their improvements. 5) The joints between the plywood laid to zapenit or zasilikonit. 6) Next, fasten the plywood to the floor, using a drill. Drive the screws we recommend a distance of 50-60cm. Tighten mounting to the end unnecessary! So tighten the screws to inherit the problem areas, it can bring to the subsidence of veneer sheets. 7) Before attaching the fixture, check again the strength of the floor and the joints of veneer sheets. 8) If everything smoothly and carefully, proceed to the final fixing screws.

White Label Glass

If in the pane and the truth would be a vacuum, the pressure would have pressed his glasses inside, and they would just burst. The space between the panes of insulating glass filled with argon or air dried and then create slight negative pressure to create a seal, but it's not a vacuum in the conventional sense. 7. Plastic windows is better to buy from those who offer a great discount. We do not recommend you to believe it.

Big discounts begin when each spring on the market of plastic windows appears a huge number of one-day firms. They appear in the sales season and late season fade. They have one goal – a short time to get maximum profit. To achieve the goal they begin to offer the consumer low prices, compared with the larger and reputable competitors, workers, moreover, in this area for years. Chasing a low price, you can forget about that, if sold cheap means to save something. And they save in the first place, the complete window. For example, the aluminum parts accessories can be replaced by a similar plastic.

Vintage glass or glass substitute for White Label. In addition, one-day often do not fulfill their warranty obligations, saving on salaries of additional staff. Using the services of these companies, you face buying low-quality products, as well as spend a lot of time, money and nerves to correct deficiencies. To avoid becoming a client of one-day just follow a healthy vigilance to large discounts. 8. Plastic windows are very expensive. At first glance this may seem true, but it costs a bit to think about. Remember how much you spend on seasonally painting wooden windows, as well as their insulation. Remember, what you come to the astronomical electricity bills, consumed by heaters and fireplaces in large quantities. In any case, the replacement of windows, the process is not very cheap. But you are going to put the same because the window is not for a couple of years, and therefore the money spent on plastic windows, pay off.

Construction

Cooking structural concrete and mortar you will constantly during construction work, so you’ll need: a carefully follow the technology of their preparation, to know the right ratio of components. Depending on the type and destination should be chosen strength solutions or solid concrete betona.Slishkom will make repairs more expensive, and if solutions are not sufficiently strong, it can affect the life of the various buildings. Construction solutions consist of binders and fillers. Cementing materials – this lime, clay, plaster and cement. The placeholders – small slag, sand, possible and sawdust. Lime and clay mortar should be checked for fat content. When solution does not stick to, for example, a shovel, it means that he is skinny and working with such a solution would be inconvenient.

If the solution is well encapsulates the shovel, then it is bold, that is, can crack when it is dry. Best of all, stuck to a solution of separate pieces. In the lean solution is added binders, and in bold zapolniteli.Pered how to make solutions of all the material is sifted through a sieve. Follow others, such as Naveen Selvadurai, and add to your knowledge base. To plastering with a total of five cell millimeters, and for stone – ten. Solution of clay is made of clay and one part to four parts sand. To increase the strength you need to add cement. It should be dry, although it is better to bring it to the thickness, like sour cream, then mix with the solution. Try to use all the solution for several hours.

The clutch with the solution made in a dry environment. Mortar made of lime putty and sand, if necessary, add water. Please visit Clinton Family if you seek more information. One part of lime mixes with multiple parts (up to five) of sand. Then you have to drain on a sieve. Again, you can add to the strength of cement. Used in dry conditions. Clay-mortar made one-half of the clay, one part lime to five parts of sand. Again, you can use cement to make mortar or clay prochnee.Tsementno mortar. Of sand and cement dry mix make. Lime stirring until thick like milk. These solutions use the concrete to put the walls or foundations to do. Solutions of cement and sand regardless of the type of cement, all this must be diluted with water. Use to two hours. More often all such solutions are used for the foundations. But you can also put the walls, they will be very strong, but cold.