Advanced Energy Systems NY

Chalky ceilings and walls go back to the previous day. Urgent tone that could revolutionize long after the monotony and lack of imagination. At this point occurs a qualitative leap in the approach to the design interiors – a period of fresh ideas and creative experiments. Moden individualism, which changes the perception of interior design. And most of all it promotes artistic design interior decoration, in the first turn, the decorative painting of walls.

In combination with various methods of drawing, painting walls can rearrange each room unique and creative, to transform the interior. Acceptance of the wall paintings in which the use template will provide an opportunity to demonstrate their uniqueness readily available means, and thus allows to make a lot of originality and diversity in interior design. A few words about the readiness to work. Before beginning work on decorating the walls, she was preparing to paint. To attain to the level of the wall with putty, primer, and superimposed over the entire range of painting the walls. Once the dry wall on it can be applied decoration. Surface redecorated and ready for painting walls. After drying, begin to spray the main image.

Murals on the pattern. Before creating the stencil you want to make a thumbnail image should not be difficult, so it can be cut, but non-trivial on bending lines. After cutting the image is transferred to a large sheet of paper. If the paper is not enough, then stick some leaves. Pattern cut along the line to get a good template for the application of spray paint. Made a stencil attached to the wall with scotch tape on a paper basis. Spray paint stencil fill the resulting image. Better just take two shades of paint, lighter and more saturated. The paint is required to cause not a lot, and divorce, that the future picture could blikovat. Once the template is dry, remove it from the wall – get the necessary Fig. Moreover, if the wall underneath a textured, the pattern will also textured. Further, the figure should be given the color stops, take shape, and give a certain amounts. The pattern is appended with a brush and acrylic paint a little darker in color than used in painting the walls. The paint is applied only to those places that you want to take. After drying, the image is put a light layer securing lacquer in an aerosol. Get a colorful and original accent, which will attract interest and make an unusual and compelling every interior design.

If not drill in the workshop mechanic lover, you can make with their hands so the machine from scrap materials and components. Because of a technological breakthrough in photofission, obsolete hundreds of thousands enlargers. They are gathering dust in a closet and attics, and many simply did not hand up to throw them, because they look brand new, and often they are associated with pleasant memories. Of course, the magnifying glass can be unscrew, and the wire with socket for light bulbs used as portability. Not in such quantity, but lacking in the same places of storage for items that throw a pity, household whisk – mixers, in which plastic worm gear drive is erased.

Of course, if you set a cap-grinder, throw, normally, not in a hurry, though, and pray for coffee or sugar in the attachment of a new mixer. Of the details outdated enlarger and a half Broken mixer is quite possible to build small, you want an amateur studio, drill. Enlarger is taken from a table-base with a reception at which the vertically moving carriage with a lamp, lens, and etc. And from the mixer – electric motor with a system of change of velocity (speed or smoothly varying). The first thing to wear on the motor shaft chuck for drills with a diameter of about 6 mm. Carved on its own bushing with the Morse taper is problematic, so you can order this item. Everything else can be done in not very equipped workshop.

Pliers, wire cutters, bolts, nuts, screwdrivers, wrenches, etc. – there have Designers enthusiasts. Yes, and calipers to measure – not a rarity in their workshops. Screw the motor to the carriage enlarger can be in different ways, depending on their structural features. Can use, or a rectangle of sheet aluminum or Plexiglas, or press the motor yoke of tin (preferably stainless steel tank from Soviet washing machine). Not far from the bar magnifier can be Screw the box with the switch and switch speed mixer, from which one side goes the cable for connection to an electrical outlet, preferably with a grounding wire. The second flexible cable with a length designed for maximum lift carriage, is connected to the motor and presses the ink cartridge clamp. Depending on the electrical mixer, cables needed to 5-6 wires. Setting up a homemade drill the machine is reduced to equalize the vertical axis along which the drill will move up and down. You can further screw beneath the point of lowering the drill small gripe, but in extreme cases – clamp, for which screwed to the table a special corner.